 |
LABEL APPLICATION INSTRUCTIONS
STANDARD PRINTED IRON-ON LABELS
IMPORTANT!! DO NOT USE STEAM
PREPARATION :
1. Set iron to cotton setting TURN THE STEAM OFF and ALLOW TO HEAT UP
2. Run iron over area of application to remove creases and unevenness.
APPLICATION: JUST 3 EZE STEPS
1. Position label on garment printed side up or if using a blank label make sure the SHINY SIDE is facing up.
2. Firmly press the iron on to the label for A FULL 12 SECONDS, Move the iron all over the label. Ensuring all edges are covered.
3. After adhesion, ALLOW TO COOL before use. Try to peel label off with your fingernail.( If you can peel even a small edge of the label, your iron is not hot enough). Use another iron or re-apply it with more pressure for 15 to 20 seconds being careful not to scorch delicate garments.
|
|
 |
WOVEN IRON-ON NAME TAPES
IMPORTANT!! DO NOT USE STEAM
Set the temperature of the iron to between Wool/Cotton DO NOT USE STEAM. Make sure the garment is COLD. Place the Name Tape on a flat part of the garment then quickly and firmly stamp the HOT iron onto the Name Tape and hold still with firm pressure for twenty seconds. More pressure can be applied if you use the edge of the iron.
IT IS IMPORTANT NOT TO HESITATE OR HOVER OVER THE NAME TAPE - THIS WILL CAUSE THE NAME TAPE TO CURL.
Do not move the iron around whilst counting for twenty seconds. Smooth out any crinkles AFTER the twenty second period has elapsed.
If the Name Tape has curled the iron has NOT been hot enough or you have hovered over the Name Tape before placing the iron onto the tape. Some garments may be considered too delicate for the temperatures required. In this case the Name Tape can be applied to the garments own existing label or sewn on in the normal way. If the tapes curl then increase the temperature of the iron and increase the time holding the iron onto the tape. We suggest trying the Name Tapes on an old tea towel before applying to garments. We have supplied Test Tape of extra nametapes for this purpose.
|
|
PLEASE NOTE : NEW CLOTHES are made using various finishes, therefore it is recommended that
they be wash and dried before the label is applied.
WOOL AND SYNTHETICS (SOCKS & SWEATERS) EZE PZE LABELS can be successfully applied to these kind of garments, but care must be taken not to scorch the material.
OTHER SYNTHETIC MATERIALS WITH A "SMOOTH FINISH" are likely to scorch at the
Recommended temperature. It may be advisable to sew on the EZE PZE LABEL to this type of material. We suggest that if you are in any doubt about the effect of heat on your garment that you refer to the Manufacturer's recommendations. In our instructions it is attempted to cover most contingencies in order that you can obtain the most possible adhesion and wash ability from your EZE PZE LABEL. If the
Instructions are followed they will withstand in excess of 60 washes. However, in certain circumstances where irons are not functioning correctly and temperature settings are incorrect, allowances must be made, using your own judgement. It is suggested, for best results, that you test iron a label onto a piece of clothing and wash or dry-clean. If the label is peeling off at the edges then it means that incorrect pressure or temperature was used. However this can normally be rectified by re-applying your iron before the next wash following the application procedures.
IMPORTANT NOTICE: If the labels are not applied to a garment within a period of 24 months, the adhesive might deteriorate and could cause the label to come away from the garment. No guarantees/refunds or replacements apply after this time.
|
 |
 |
EZE STICK SHOE & PROPERTY LABELS (White Material Based Labels)
These labels have been supplied for "sticking" onto items that WILL NOT be placed into a washing machine. They are self adhesive semi permanent labels and can be moved from items usually without leaving a mark.
They are great for Shoes/Lunch boxes and other bits of school kit like books.
|
|
 |
PEEL 'n' STICK PROPERTY & SHOE LABELS. (Coloured Plastic Based Labels)
These self adhesive labels are ideal for all school items and are very useful on a variety of personal belongings.
These labels are considered permanent and once applied can not be moved. The following steps may assist you in applying these labels.
1) FOOTWEAR Apply the label to the instep of the shoe. Press firmly and then place clear protective cover over the top.
Do not apply to warm or damp footwear. Leave overnight to adhere securely.
2) STATIONARY & Other Property
Press firmly and apply clear protective cover. Allow 2 hours for secure adhesion.
These labels are not suitable for rough or uneven surfaces
|
|
 |
SEW IN NAME TAPES & WOVEN LABELS
Cut between the two bars, fold over the edges and sew through the folded tape and into the garment at each end.
|
|
